Products

Flowell manufactures Meter Tubes utilizing orifice flanges, orifice fittings and other primary flow devices such as ultrasonic and turbine meters. Flowell MeterTubes are designed to ASME B31.8 for gas transmission and distribution piping as a standard and comply with API 14.3 or ISO 5167 standards to meet your requirements and assure accurate measurement. All of [...]

Flowell offers strainers in Carbon Steel and Stainless Steel, ranging in sizes 1″ to 24″ with open area of strainers from 100% to 300%, using different sizes of liner or mesh wire.

Flowell Universal Type Orifice Plates are designed to be used with ring joint plate holders. Standard industry sizing also allows our plates to be used with any of the dual or single chambered orifice fittings on the market. Flowell stocks 2″ through 12″ sizes in 1/8″ and 1/4″ thicknesses in both 304 and 316SS. Other [...]

Flowell Spectacle (Figure 8) Blinds thicknesses are in accordance with API 590 to assure that these units will withstand the temperature and pressure of an ANSI rated flange. Carbon steel units are available from stock. 304 and 316 stainless steel units are also readily available. Other materials are available on request.

Flowell Paddle Spacer and Blinds thicknesses are accordance with API 590 to assure that these units will withstand the temperature and pressure of an ANSI rated flange. Carbon steel units are available from stock. 304 and 316 stainless steel units are also readily available. Other materials are available on request.

Flowell Studding Outlets are manufactured in accordance with ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 (UG-11 (a)(1)) unless otherwise specified. Standard material of construction is carbon steel (ASTM A105). The outside diameter and raised face dimensions of the outlet is as specified in ANSI B1.5. Flat bottom shall be provided as a [...]

Flowell Bleed Rings are designed for installation within the bold circle of raised face flanges. One ½” fnpt tap is provided in each ring. Standard material is carbon steel but other materials are available on request. While primarily used to bleed gas or liquid from a line, they may also be manufactured with a full [...]

Flowell Condensate Chambers are designed to trap condensate and foreign matter that may accumulate in gaseous service lines. They are also effective for providing a liquid seal on steam and corrosive service lines. Condensate chambers are available in schedule 40, XH and XXH pipe schedules and are considered to have the same pressure rating as [...]

Flowell Straightening Vanes are designed to be installed in piping upstream of an orifice plate. When used with recommended minimum pipe lengths, they reduce flow disturbances caused by upstream piping configurations or valves. Flowell manufactures both line mounted and flanged models in carbon steel and 304 and 316 stainless steel. Every vane is built to [...]

Flowell Flow Nozzles are manufactured in accordance with ASME MFC-3M and ANSI B31. Standard material is stainless steel with other corrosion resistant materials available on request. Styles included: Flanged – for installation between pipe flanges; Flanged Throat Tap – similar to the standard flanged style with the downstream tap machined as a part of the [...]

Flowell manufactures Venturi Tubes in a variety of sizes and styles to meet a wide range of applications. Flanged End, Weld-In and Low-Loss styles are available. Venturis can be used with virtually any gas, liquid, steam, slurry or sludge. Built in accordance with ASME Fluid Meters and ASME MFC-3M, these meters provide a high degree [...]

Flowell Ring Joint Orifice Plate Holders are designed to be mounted between Ring Joint Orifice Flanges Style 590 utilizes a set of hold-down screws to secure a replaceable universal orifice plate. (Plate and holder are sold separately.) Style 560 is an integral design with the plate and hold machined as one piece. Style 590 is [...]

Flowell Paddle Type Orifice Plates are designed to be used with orifice flanges. Skilled craftsmen and state-of-the-art machining practices assure that our plates meet or exceed the stringent requirements of API 14.3, ISO 5167 and ISA RP3.2. All plates come with a standard 30 RMS surface finish unless otherwise requested. Flowell stocks 1/8″ to 1/2″ [...]

Flowell Orifice Flange Unions provide an economical method of measuring flow in both gas and liquid services. Flanges are machined in accordance with the requirements of ANSI B16.36. Raised face flanges meet the requirements of ANSI B16.5 for raised face dimensions. Our standard pressure taps, bore tolerances and surface finishes are all in accordance with [...]